Showing posts with label relay. Show all posts
Showing posts with label relay. Show all posts
Monday, September 22, 2014
Fuse Box Toyota 1990 4runner Relay Diagram
Fuse Box Toyota 1990 4runner Relay Diagram - Here are new post for Fuse Box Toyota 1990 4runner Relay Diagram.
Fuse Panel Layout Diagram Parts: charge, hazzard horn, dome light, headlight, alternator, headlight control relay, EFI relay, EFI relay, CMH relay.
Continue reading...
Fuse Box Toyota 1990 4runner Relay Diagram
Fuse Panel Layout Diagram Parts: charge, hazzard horn, dome light, headlight, alternator, headlight control relay, EFI relay, EFI relay, CMH relay.
Friday, June 6, 2014
Simple Solar Relay Circuit Diagram
Build a Simple Solar Relay Circuit Diagram.With extended periods of bright sunshine and warm weather, even relatively large storage batteries in solar-power systems can become rather warm. Consequently, a circuit is usually connected in parallel with the storage battery to either connect a high-power shunt (in order to dissipate the excess solar power in the form of heat) or switch on a ventilation fan via a power FET, whenever the voltage rises above approximately 14.4 V. However, the latter option tends to oscillate, since switching on a powerful 12-V fan motor causes the voltage to drop below 14.4 V, causing the fan to be switched off. In the absence of an external load, the battery voltage recovers quickly, the terminal voltage rises above 14.4 V again and the switching process starts once again, despite the built-in hysteresis.
Simple Solar Relay Circuit Diagram
A solution to this problem is provided by the circuit shown here, which switches on the fan in response to the sweltering heat produced by the solar irradiation instead of an excessively high voltage at the battery terminals. Based on experience, the risk of battery overheating is only present in the summer between 2 and 6 pm. The intensity of the sunlight falling within the viewing angle of a suitably configured ‘sun probe’ is especially high precisely during this interval. This is the operating principle of the solar relay.
The trick to this apparently rather simple circuit consists of using a suitable combination of components. Instead of a power FET, it employs a special 12-V relay that can handle a large load in spite of its small size. This relay must have a coil resistance of at least 600 Ω, rather than the usual value of 100-200 Ω. This requirement can be met by several Schrack Components relays (available from, among others, Conrad Electronics). Here we have used the least expensive model, a type RYII 8-A printed circuit board relay. The light probe is connected in series with the relay. It consists of two BPW40 photo-transistors wired in parallel.
The type number refers to the 40-degree acceptance angle for incident light. In bright sunlight, the combined current generated by the two photo-transistors is sufficient to cause the relay to engage, in this case without twitching. Every relay has a large hysteresis, so the fan connected via the a/b contacts will run for many minutes, or even until the probe no longer receives sufficient light. The NTC thermistor connected in series performs two functions. First, it compensates for changes in the resistance of the copper wire in the coil, which increases by approximately 4 percent for every 10 ºC increase in temperature, and second, it causes the relay to drop out earlier than it otherwise would (the relay only drops out at a coil voltage of 4 V).
Depending on the intended use, the 220-Ω resistance of the thermistor can be modified by connecting a 100-Ω resistor in series or a 470-Ω resistor in parallel. If the photo-transistors are fastened with the axes of their incident-angle cones in parallel, the 40-degree incident angle corresponds to 2 pm with suitable solar orientation. If they are bent at a slight angle to each other, their incident angles overlap to cover a wider angle, such as 70 degrees. With the tested prototype circuit, the axes were oriented nearly parallel, and this fully met our demands. The automatic switch-off occurs quite abruptly, just like the switch-on, with no contact jitter. This behavior is also promoted by the NTC thermistor, since its temperature coefficient is opposite to that of the ‘PTC’ relay coil and approximately five times as large.
This yields exactly the desired effect for energizing and DE-energising the relay: a large relay current for engagement and a small relay current for disengagement. Building the circuit is actually straightforward, but you must pay attention to one thing. The photo transistors resemble color less LEDs, so there is a tendency to think that their ‘pinning’ is the same as that of LEDs, with the long lead being positive and the short lead negative. However, with the BPW40 the situation is exactly the opposite; the short lead is the collector lead. Naturally, the back-emf diode for the relay must also be connected with the right polarity. The residual current on cloudy days and at night is negligibly small.
Sunday, October 6, 2013
Audio Amplifier Output Relay Delay
This is a simple circuit which I built to one of my audio amplifier projects to control the speaker output relay. The purpose of this circuit is to control the relay which turns on the speaker output relay in the audio amplifier. The idea of the circuit is wait around 5 seconds ofter the power up until the speakers are switched to the amplifier output to avoid annoying "thump" sound from the speakers. Another feature of this circuit is that is disconnects the speaker immediately when the power in the amplifier is cut off, so avoiding sometimes nasty sounds when you turn the equipments off.
Parts
C1 = 100 uF 40V electrolytic
C2 = 100 uF 40V electrolytic
D1 = 1N4007
D2 = 1N4148
Q1 = BC547
R1 = 33 kohm 0.25W
R2 = 2.2 kohm 0.25W
RELAY 24V DC relay, coil resistance >300 ohm
Circuit operation:
Then power is applied to the power input of the circuit, the positive phase of AC voltage charges C1. Then C2 starts to charge slowly through R1. When the voltage in C2 rises, the emitter output voltage of Q1 rises together with voltage on C2. When the output voltage of Q2 is high enough (typically around 16..20V) the relay goes to on state and the relay witches connect the speakers to the amplifier output. It takes typically around 5 seconds after power up until the relay starts to conduct (at absolute time depends on the size of C2, relay voltage and circuit input voltage). When the power is switched off, C1 will loose its energy quite quickly. Also C2 will be charged quite quickly through R2. In less than 0.5 seconds the speakers are disconnected from the amplifier output.
Notes on the circuit:
This circuit is not the most accurate and elegant design, but it has worked nicely in my small home-built PA amplifier. This circuit can be also used in many other applications where a turn on delay of few seconds is needed. The delay time can be increased by using bigger C2 and decreased by using a smaller C2 value. Note that the delay is not very accurate because of simplicity of this circuit and large tolerance of typical electrolytic capacitors (can be -20%..+50% in some capacitors).
Continue reading...
PartsC1 = 100 uF 40V electrolytic
C2 = 100 uF 40V electrolytic
D1 = 1N4007
D2 = 1N4148
Q1 = BC547
R1 = 33 kohm 0.25W
R2 = 2.2 kohm 0.25W
RELAY 24V DC relay, coil resistance >300 ohm
Circuit operation:
Then power is applied to the power input of the circuit, the positive phase of AC voltage charges C1. Then C2 starts to charge slowly through R1. When the voltage in C2 rises, the emitter output voltage of Q1 rises together with voltage on C2. When the output voltage of Q2 is high enough (typically around 16..20V) the relay goes to on state and the relay witches connect the speakers to the amplifier output. It takes typically around 5 seconds after power up until the relay starts to conduct (at absolute time depends on the size of C2, relay voltage and circuit input voltage). When the power is switched off, C1 will loose its energy quite quickly. Also C2 will be charged quite quickly through R2. In less than 0.5 seconds the speakers are disconnected from the amplifier output.
Notes on the circuit:
This circuit is not the most accurate and elegant design, but it has worked nicely in my small home-built PA amplifier. This circuit can be also used in many other applications where a turn on delay of few seconds is needed. The delay time can be increased by using bigger C2 and decreased by using a smaller C2 value. Note that the delay is not very accurate because of simplicity of this circuit and large tolerance of typical electrolytic capacitors (can be -20%..+50% in some capacitors).
Tuesday, September 3, 2013
Light Activated Relay
This is same circuit as above with the addition of a photo resistor to trigger the flip flop instead of a push button. The bias resistor in series with photo resistor was chosen so that sufficient voltage is present at the base of the 2N3904 to supply current to the circuit in ambient lighting conditions. The circuit should toggle when the photo resistor is hit by a flashlight beam or other fast changing light source. Slow changes in light intensity will have no effect unless the light gets too bright to maintain sufficient bias for the 2N3904.
Light Activated Relay Circuit diagram :
Light Activated Relay Circuit diagram :
Monday, September 2, 2013
Relay Control with MOSFET IRF511
We would like ti show you the circuit is similar to the above, but uses an N-channel MOSFET, as IRF511, 540, 640, etc. instead of the NPN transistor. Smaller MOSFETs can be used, but I do not know the part numbers. I tested the circuit with a IRF640, IRF511, IRFZ34 and REP50N06. The same circuit has three advantages, but requires only a few parts, always off to the relay and do not need a switch debounce.
In operation, when the relay is deactivated, the 100uF capacitor charge up to 6 volts. When the button is pressed, is on the capacitor 6 volts at the gate MOSFET. The capacitor voltage (and gate voltage) of 6 ms should drop to 3 volts in about 200 to move enough time for relay contacts. At very slow relay, a larger capacity. With the ratification of the relay, the contacts 12 volts to the resistance produce valid 3.3K 6 volts at the gate, holding that the relay is self-sufficient. The capacitor is then discharged to zero since the relay contact 12 is connected not to the 15K resistor.
Relay Control with MOSFET IRF511 Circuit Schematic
When the button is pressed, the capacitor is zero volts to the gate of switching off the relay. There should be no problem making the button again to be the operation of relays, since the gate voltage is only about 1.8 volts when the button is pressed and the MOSFET requires approximately 3.5 volts or more are to start running. But you wait about 1 second or more between pressing a key need, capacitor time to load or unload. Two buttons are displayed, but you could have a number of more parallel to operate the relay from multiple locations
In operation, when the relay is deactivated, the 100uF capacitor charge up to 6 volts. When the button is pressed, is on the capacitor 6 volts at the gate MOSFET. The capacitor voltage (and gate voltage) of 6 ms should drop to 3 volts in about 200 to move enough time for relay contacts. At very slow relay, a larger capacity. With the ratification of the relay, the contacts 12 volts to the resistance produce valid 3.3K 6 volts at the gate, holding that the relay is self-sufficient. The capacitor is then discharged to zero since the relay contact 12 is connected not to the 15K resistor.
Relay Control with MOSFET IRF511 Circuit Schematic
When the button is pressed, the capacitor is zero volts to the gate of switching off the relay. There should be no problem making the button again to be the operation of relays, since the gate voltage is only about 1.8 volts when the button is pressed and the MOSFET requires approximately 3.5 volts or more are to start running. But you wait about 1 second or more between pressing a key need, capacitor time to load or unload. Two buttons are displayed, but you could have a number of more parallel to operate the relay from multiple locations
Sunday, November 11, 2012
1995 Fiat Coupe Fuel Relay Circuit Diagramcircuit Schematic
Find More Information About 2002 Bajaj Legend Wiring Diagram Here.
About Toyota Celica Wiring Diagram And Electrical System Here.
1975 Mercedes Benz 280 S Wiring Diagram And Electrical Troubleshooting.
Audi Quattro Wiring Diagram And Electrical Schematic 2004 Circuit.
Jaguar Xj6 Series 3 Car Schematic Diagram 1979 1986.
Nissan Titan Wiring Diagram And Body Electrical Parts Schematic.
A340e Shift Lock System Wiring Diagram Circuit Schematic.
Keywords 2002 Ford F150 Wiring Diagram 2002 F150 Ignition Wiring 2008.
1995 Fiat Coupe 16v Fuel Relay Circuit Diagram Circuit Schematic.
1966 Volkswagen Beetle Headlight Switch Wiring Circuit Schematic.
Subscribe to:
Posts (Atom)